Skip to main content

Maintenance

FBCN centrifugal pump maintenance

Identify your FBCN bearing bracket, shaft seal and parts before planning maintenance. Locate lubrication points, distinguish sealing arrangements and prepare a spare parts request.

FBCN series centrifugal pump set on a base
FBCN series — photograph from the FB Bombas collection.
Quick answer

Start with the model, bearing bracket and installed shaft seal. The FBCN has oil-lubricated bearings, packing or a mechanical seal, and back-pull-out construction that allows bearing assembly removal without disconnecting the piping. Select parts for the actual pump configuration.

FBCN Series

FB Bombas pump for this application

FBCN pump and motor set on a base, from the FB Bombas collection

Need parts for your FBCN?

The FBCN uses packing or a mechanical seal, with parts specific to each arrangement. Identify the installed configuration when requesting spares.

Source: Manual FBCN MTEC-03/00, p.7 e p.10, Tabela 5

In this article · 7

Identify the FBCN before ordering parts

Start maintenance planning by identifying the pump. Photograph the nameplate and record the full model, serial number, bearing bracket and installed shaft seal. The FBCN parts list identifies the nameplate as part 970.

The external dimensions of this range broadly follow ISO 2858. Use your pump identification and the installed configuration’s parts list to select replacement components.

Bearings: oil, level indication and bearing reference

FBCN bearings are oil-lubricated, with a dipstick or an optional automatic replenishing oiler. Keep this circuit separate from the shaft sealing arrangement: bearing oil and the liquid used at the shaft seal serve different assemblies.

The bearing reference depends on the bracket. These examples show why a spare parts request needs the bearing bracket identification:

  • Oil level indicator: part 639.
  • Bearing housing drain plug: part 903.4.
  • Lip seals: reference 421, quantity of two in the parts list.
Source: FBCN manual MTEC-03/00, p.5, Table 1 (Portuguese). Examples by bracket.
Bearing bracketBearing reference
306306 C3
406308 C3

Shaft sealing: distinguish packing and seal parts

The FBCN shaft has a protective sleeve at the sealing area. The pump can use packing or a mechanical seal, with different parts for each arrangement. Identify the installed shaft seal components before preparing the order.

Source: FBCN manual MTEC-03/00, p.10, Table 5, shaft seal applicability notes (Portuguese).
Shaft sealIdentified parts
Packing452 — packing gland; 461 — packing.
Mechanical seal433 — mechanical seal.

Identify the installed sealing arrangement

The configuration code distinguishes internal sealing, an external liquid supply and flushing. Record the code and the existing connections when planning maintenance. Configuration S, with a mechanical seal, is defined to suit the application and the request.

Source: FBCN manual MTEC-03/00, p.11, sealing arrangements (Portuguese).
ConfigurationCircuit and application
STLubrication by the pumped liquid and internal sealing, for clean, non-aggressive fluids.
S1Sealing with clean external liquid; applications include suction from a tank under vacuum.
S2External lubrication and sealing for fluids containing suspended solids or small fibres.
S3Flushing with clean external liquid for abrasive particles or a tendency to crystallise.
S4Thermal oil service with pure graphite packing and/or graphite with carbon fibre.
Engineering note

Applications using an external liquid supply cannot use a cooling chamber. Identify the configuration before specifying auxiliary connections for the work.

Back-pull-out construction, wear rings and gaskets

Back-pull-out construction allows the bearing assembly to be removed from the volute without disconnecting or disturbing the alignment of the pump piping. When planning replacement parts for the assembly, also identify the wear rings and the gaskets at each joint.

The casing has a wear ring on the suction side. Impeller wear ring applicability varies with pump size; do not order wear rings using the series name alone.

Source: FBCN manual MTEC-03/00, pp.7 and 10, Table 5 (Portuguese). Check impeller ring applicability by size.
ReferenceComponent
502Casing wear ring.
503Impeller wear ring, where applicable to the pump size.
400.1Flat gasket between casing and pressure cover.
400.2Flat gasket between bearing cover and bracket.

Record rotation direction and connections

FBCN rotation is clockwise when viewed from the drive end. When preparing the return-to-service documentation, identify the lubrication, drain and sealing connections. The alignment and vibration guides support assessment of the assembly.

Source: FBCN manual MTEC-03/00, p.12, Table 6 (Portuguese). Rotation: p.5, Table 1.
ConnectionIdentification
L1Lubrication.
D2Bracket drain.
Se / SsSealing liquid inlet / outlet.

Send your FBCN details for parts and maintenance

Prepare the request:

  1. send the series, full model, serial number and nameplate photo;
  2. identify the bracket, shaft seal and sealing arrangement;
  3. specify the part, reference and parts table used;
  4. describe the fluid, operating conditions and observed symptom.

Use these details to request the configuration-specific information needed to complete your maintenance plan from FB Bombas Engineering:

  • Oil specification, quantity, fill level and change interval; in-service inspection frequency.
  • Clearances, wear limits, tightening torques, shaft seal adjustment and disassembly and assembly procedure; wear ring applicability by size.
  • Isolation, decontamination, storage preservation and post-repair startup procedures, with acceptance criteria and temperature conditions for the configuration.

Frequently asked questions

Answers about the topics covered in this article.

Can the FBCN bearing assembly be removed without disconnecting the piping?

Yes. Back-pull-out construction allows the bearing assembly to be removed from the volute without disconnecting or disturbing the alignment of the pump piping. To plan the parts needed, identify the pump model, bearing bracket and installed shaft seal; references vary with the assembly.

Does the pumped liquid lubricate FBCN bearings?

FBCN bearings are oil-lubricated, with a dipstick or an optional automatic replenishing oiler. In configuration ST, the pumped liquid provides lubrication and internal sealing for clean, non-aggressive fluids. That sealing arrangement is separate from the bearing lubrication circuit.

Does every FBCN use the same bearing?

No. The bearing reference depends on the bearing bracket. Bracket 30 uses reference 6306 C3; bracket 40 uses 6308 C3. Include the bracket identification with the model and serial number so the part can be checked against your assembly.

Are the parts lists different for packing and mechanical seals?

Yes. An FBCN with packing uses the packing gland and packing references, while the mechanical seal configuration has its own seal reference. The shaft has a protective sleeve at the sealing area. Identify the installed shaft seal before requesting components.

Sources and citation (1)
  1. FB Bombas — Manual Técnico FBCN — MTEC-03/00

Discuss your application with FB Bombas