How is pump sizing performed?
The review considers the fluid, flow, required pressure or head, temperature, viscosity and installation conditions. Provide what you already know and identify any equipment in use. The team checks the necessary data before confirming series, model, drive and materials.
Is FB Bombas a national alternative to imported manufacturers in Queimados?
FB Bombas is a Brazilian manufacturer with direct service from its factory. To compare an alternative for the project, check performance, materials, dimensions, documentation and commercial conditions. Brazilian origin alone does not guarantee lower cost, shorter lead time or technical equivalence.
How to request a technical quote for industrial pumps in Queimados?
Send the application, fluid, temperature and available flow, pressure or head data. For replacement, add the equipment model, identification and drawing. Also state the destination and purchase documentation requirements. The team confirms any additional data needed and the technical and commercial proposal scope.
Does the FBOT series serve thermal oil applications in Queimados?
Yes. The FBOT is the FB Bombas series developed for pumping organic thermal oils.
The FBOT series range allows temperatures up to 350 °C and uses back pull-out construction (MTEC-16/00), which allows the bearing-housing assembly to be removed without disconnecting the piping; the maximum discharge pressure varies with temperature (Figure 1 of the manual), and the fluid must not contain abrasive particles.
For the circuit, send the oil identification and technical data sheet, the start-up and operating temperatures and the flow and head duty point; model, materials and sealing are confirmed for the circuit.
What types of fluids can FB Bombas pumps handle?
It depends on the series. The catalogue for the FBE external gear pump lists oils in general, greases, asphalt, diesel oil, kerosene, paints, varnishes, resins and solvents, as well as lubrication systems and hydraulic equipment. The FBEI internal gear pump is intended for high-viscosity liquids.
The FBCN and FBME handle clean or turbid liquids, and the FBOT handles organic thermal oils free of abrasive particles and of substances that chemically attack the pump. For the process, state the composition, temperature, viscosity and solids content; fluids with suspended solids must be assessed by FB Bombas engineering.
Are FB Bombas pumps delivered to Queimados with a traceable Data Book?
When the Data Book is part of the purchase scope. State which drawings and manuals are required; the proposal confirms the documents applicable to the supplied series and configuration. The same Data Book is not assumed for every pump.
How to request a pump quote for Queimados?
Use the website form, WhatsApp +55 11 97287-4837 or comercial@fbbombas.com.br. Describe the project, fluid and technical data you already have. The team reviews the application, clarifies missing information and confirms the configuration and proposal conditions.
Is it possible to replace an imported pump with an FB Bombas pump?
Yes, once equivalence has been confirmed. FB Bombas replaces the installed pump with a complete FB Bombas pump and, before the order, assesses the installation and sends a data sheet and dimensional drawing.
For the installation, send the identification and drawing of the current pump, with its duty point, fluid, materials and drive; origin or a similar designation does not guarantee direct replacement.
Are FB Bombas pumps energy efficient?
It depends on the model and the duty point; there is no single efficiency figure for the brand. The FBCN and FBME characteristic curves show the efficiency of each model and, for stainless-steel impellers with passages up to 15 mm, the FBCN manual deducts 2 or 3 points from the curve efficiency (Table 4).
For the project, compare the absorbed power at the process flow, head and fluid, also considering drive, control and operating duty.
Which pump does FB Bombas recommend for water and utilities in Queimados?
The FBCN, a standardized centrifugal pump for clean or turbid liquids, with a series range of up to 2,200 m³/h and 135 m; when a higher head is required, the multistage FBME reaches 300 m. Each model has its own limits in the manual tables.
For the project, state the fluid and the flow and head duty point; selection checks the model curve, suction conditions, materials, drive and installation interfaces.