Industrial pumps for projects in Xangri-lá, Rio Grande do Sul

FB Bombas began manufacturing industrial pumps in 1944. Its current factory is in Cabreúva, Brazil. The Our History page presents the company’s development; each series’ technical documentation supports equipment evaluation for your project in Xangri-lá.

Yes, for FB product lines. The FBE catalogue lists replacement components such as shafts, gears, bushing sets, covers, mechanical seal, lip seal and relief valve, and the FBEI and FBME manuals include spare-parts lists for two years of operation. For delivery to Xangri-lá, state the series, model, manufacturing number and component; compatibility, availability and lead time are confirmed in the quotation. Supply ships from the factory in Cabreúva, Brazil; the city page does not indicate local stock. Use original parts: the FBME service manual makes the operating and performance warranty conditional on original parts and FB’s consent.

It depends on the model and the duty point; there is no single efficiency figure for the brand. The FBCN and FBME characteristic curves show the efficiency of each model and, for stainless-steel impellers with passages up to 15 mm, the FBCN manual deducts 2 or 3 points from the curve efficiency (Table 4). For the project in Xangri-lá, compare the absorbed power at the process flow, head and fluid, also considering drive, control and operating duty.

It depends on the series. On the FBCN and FBOT, back pull-out construction allows the bearing-housing assembly to be removed without disconnecting the piping, and the FBEI catalogue also indicates back pull-out construction. The FBE external gear pump is not back pull-out: its shafts are supported on bushings. Before working on the equipment in Xangri-lá, check the series manual, the sectional drawing and the parts list.

When the Data Book is part of the purchase scope. State which drawings, manuals, certificates and test reports are required for Xangri-lá; the proposal confirms the documents applicable to the supplied series and configuration. The same Data Book is not assumed for every pump.

Send the series and model of the pump installed in Xangri-lá, the operating conditions and the available vibration records; the standard, measurement points and limits are defined for the assembly, with no single limit for every pump. Check the alignment first: the FBEI (MAN001-10) and FBME (MSERV-08/01) manuals identify pump-to-motor misalignment as a source of vibration and premature wear and call for realignment after final installation, because transport usually misaligns the set, which leaves the factory pre-aligned; the stated tolerance is under 0.05 mm radial and 0.6° angular, according to the coupling supplier.

It can, especially with viscous fluids. On the FBE, speed and transmission are set by fluid viscosity (Table 2 of manual MTEC-01/01), and the heating chamber is available only on sizes from 1.1/2" to 6". The FBEI manual requires the fluid to be at the proper temperature and viscosity before start-up and the heating jacket to be supplied gradually, with steam up to 185 °C or thermal fluid up to 232 °C, both up to 10 bar. State the minimum site temperatures and the fluid viscosity at start-up and in operation in Xangri-lá.

FB Bombas supplies the complete FBCN and checks, model by model, the dimensions in manual MTEC-03/00 (baseplate, nozzles, flanges and shaft) and the duty point before the order. The manual states mechanical construction per ASME B73.1; dimensional interchangeability with the existing pump is not assumed and is confirmed on the drawing. Send the identification and drawing of the pump installed in Xangri-lá, with flow, head, fluid, materials and drive.

Yes, once equivalence has been confirmed. FB Bombas replaces the installed pump with a complete FB pump and, before the order, assesses the installation and sends a data sheet and dimensional drawing. For the installation in Xangri-lá, send the identification and drawing of the current pump, with its duty point, fluid, materials and drive; origin or a similar designation does not guarantee direct replacement.

Lead time to Xangri-lá depends on the model, configuration and transport. Several FBE models are kept in stock; availability and expected dispatch for each item are confirmed in the quotation. State the destination and the date you need so that the proposal also defines freight and delivery responsibilities.