Gear & Centrifugal Pumps in Aperibé

Yes. FB Bombas is a Brazilian manufacturer accredited in FINAME (BNDES Special Industrial Financing Agency), which qualifies equipment supplied to Aperibé for BNDES Finame financing lines (Industrial Working Capital, Modernization, Capital Goods) with preferential conditions for national industry. The commercial team provides the product FINAME code on the technical proposal for inclusion in the customer financial plan.

Three fluid fronts are covered by the FB series. FBE: mineral and synthetic oils, asphalt (CAP), BPF fuel oils, petroleum derivatives, molasses, resins, viscous chemical and hydraulic products. FBCN: raw and treated water, process fluids and industrial effluents. FBOT: thermal oil at elevated temperatures. Fluid viscosity, temperature and chemical compatibility guide the sizing of every application.

Yes — Aperibé is part of FB Bombas’ direct service area. Supply, engineering support and spare parts ship from the factory in Cabreúva/SP; sizing is done at no cost and, when the project is critical, the team evaluates an on-site technical visit.

Yes. FB Bombas offers technical training for operations and maintenance teams in Aperibé, with modules on: sizing and reading the characteristic curve, identifying cavitation through NPSH, mechanical-seal troubleshooting, laser alignment, ISO 10816 vibration analysis and PM (preventive maintenance) practice with bearing and wear-ring replacement. Training can be delivered at the customer plant or at the Cabreúva/SP factory, in person or hybrid.

It does. The standard used is ISO 10816, with velocity RMS in mm/s, and the diagnosis — conducted by FB Bombas application engineering — identifies misalignment, imbalance, bearing defects and cavitation on pumps operating in Aperibé. At startup the baseline is captured; in PM campaigns, spectral comparison is performed; and interventions (re-balancing, bearing replacement, laser alignment) are recommended before vibration enters zone D.

Yes. Every FB Bombas pump delivered to Aperibé comes with a complete technical Data Book: hydraulic test certificate, material certificates (stainless, duplex, ductile cast iron per spec), ISO 21940 G2.5 balancing report, characteristic curve measured on the bench, API 682 mechanical-seal data sheets, operation and maintenance manual, and as-built drawings. All documentation is traceable by the unit serial number.

The portfolio covers four in-house series: FBE (external gear) for viscous fluids, FBEI (internal gear) for low-pulsation services, FBCN (standardized centrifugal) for water and light fluids and FBOT (dedicated centrifugal) for thermal oil — plus complete fire-fighting systems per NFPA 20 and NBR 16704.

The FB Bombas rotating set is balanced per ISO 21940 G2.5 (a balancing grade equivalent to API 610 requirements for heavy-duty service) — required for critical projects in Aperibé with continuous regime, plants with online vibration monitoring or applications with high cost of unplanned downtime. For machines running above 3,600 RPM or with rotating mass over 50 kg, balancing is performed on two planes with a piezoelectric sensor.

During a plant shutdown in Aperibé, critical parts — mechanical seal, impeller, shaft, wear ring, bearings — enter FB Bombas' emergency flow: pre-invoicing, priority dispatch and choice of alternative modal (express road or air, depending on distance and criticality). Typical lead time depends on the region and the window is negotiated case by case. Customers with an installed base and scheduled PM can keep part of the stock on consignment at the plant.

They do. The FBCN series dimensionally meets ASME B73.1, the North American standard for horizontal end-suction process centrifugal pumps. In practice, a Aperibé plant running a normalized pump of the same designation achieves retrofit on the already-installed baseplate: since shaft dimensions, suction/discharge flanges, casing feet and impeller centerline follow the same standard, the FBCN pump takes the place of the previous one — piping and baseplate stay intact. Hydraulic equivalence (Q×H and NPSH) is checked separately, on the data sheet.