FBE Gear Pumps in Pindaí

Who serves Pindaí is the FB Bombas factory team itself in Cabreúva/SP. In practice: direct access to application engineering for sizing, a complete technical quotation returned within 3-5 business days and original parts supplied at factory pricing. Depending on project criticality, on-site technical visits to Pindaí are added to the plan.

Yes. On the factory bench in Cabreúva/SP the FAT (Factory Acceptance Test) is carried out: hydraulic test with characteristic-curve measurement (Q × H), hydraulic efficiency, NPSHr and ISO 10816 vibration — witnessed by customer inspection when specified. The SAT (Site Acceptance Test) on Pindaí projects counts on application engineering during commissioning, including startup checklist, laser alignment and recording of the baseline vibration signature.

Yes — with a structural advantage: since the FBE, FBEI, FBCN and FBOT series are manufactured entirely in Brazil, parts ship from the factory itself in Cabreúva/SP, with short lead times for planned shutdowns and priority handling for emergencies. The direct effect is a lower total cost of ownership.

It does. FB Bombas' technical training program for operators and maintainers in Pindaí covers: characteristic-curve reading and sizing, cavitation identified via NPSH, mechanical-seal troubleshooting, laser alignment, vibration analyzed per ISO 10816 and preventive maintenance (PM) practice, including bearing and wear-ring replacement. Location and format are flexible — customer plant or the Cabreúva/SP factory, in person or hybrid.

FB Bombas manufactures four major lines: FBE (external gear) for viscous fluids, FBEI (internal gear) for lubricating fluids, FBCN (normalized centrifugal) for water and low-viscosity fluids, and FBOT (specific centrifugal) for thermal oil circuits. We also serve fire protection systems in compliance with NFPA and NBR 16704.

They do. The FBCN series dimensionally meets ASME B73.1, the North American standard for horizontal end-suction process centrifugal pumps. In practice, a Pindaí plant running a normalized pump of the same designation achieves retrofit on the already-installed baseplate: since shaft dimensions, suction/discharge flanges, casing feet and impeller centerline follow the same standard, the FBCN pump takes the place of the previous one — piping and baseplate stay intact. Hydraulic equivalence (Q×H and NPSH) is checked separately, on the data sheet.

The FB line covers a wide range: mineral and synthetic oils, asphalt (CAP), BPF fuel oils, petroleum derivatives, molasses, resins, viscous chemical and hydraulic products (FBE series); raw and treated water, process fluids, industrial effluents (FBCN series); thermal oil at elevated temperatures (FBOT series). Each application is sized according to fluid viscosity, temperature and chemical compatibility.

It is. A Brazilian manufacturer since 1944, FB Bombas runs its factory in Cabreúva/SP and keeps a technical team focused on projects in Pindaí. Across the duty ranges currently held by imported lines, the FBCN (centrifugal), FBE/FBEI (gear) and FBOT (thermal oil) series offer equivalent coverage, with better lead times by dispensing with imports, factory-direct technical support, spare parts for FB pumps and Portuguese-speaking application engineering. On a normalized pump, the existing baseplate is preserved when the ASME B73.1 dimension designation matches — which the standard makes independent of the installed brand.

Coverage against manufacturing defects accompanies the supply of FB pumps — the full terms appear in the commercial proposal. It holds as long as installation, operation and maintenance follow what the manual specifies and the sizing performed by engineering. Our technical team clarifies the specific conditions of your project in Pindaí.

FB Bombas' rotating set balancing follows ISO 21940 G2.5 — a grade equivalent to the API 610 requirement for heavy-duty service. It is the level demanded in critical Pindaí projects: continuous regime, plants with online vibration monitoring or operations where unplanned downtime is expensive. Above 3,600 RPM or with rotating mass beyond 50 kg, balancing is done on two planes, with a piezoelectric sensor.