Gear pumps for projects in Antônio Carlos, Santa Catarina

FB Bombas supplies the complete FBCN and checks, model by model, the dimensions in manual MTEC-03/00 (baseplate, nozzles, flanges and shaft) and the duty point before the order. The manual states mechanical construction per ASME B73.1; dimensional interchangeability with the existing pump is not assumed and is confirmed on the drawing. Send the identification and drawing of the pump installed in Antônio Carlos, with flow, head, fluid, materials and drive.

Yes, once equivalence has been confirmed. FB Bombas replaces the installed pump with a complete FB pump and, before the order, assesses the installation and sends a data sheet and dimensional drawing. For the installation in Antônio Carlos, send the identification and drawing of the current pump, with its duty point, fluid, materials and drive; origin or a similar designation does not guarantee direct replacement.

It depends on the series. On the FBCN and FBOT, back pull-out construction allows the bearing-housing assembly to be removed without disconnecting the piping, and the FBEI catalogue also indicates back pull-out construction. The FBE external gear pump is not back pull-out: its shafts are supported on bushings. Before working on the equipment in Antônio Carlos, check the series manual, the sectional drawing and the parts list.

Send the application in Antônio Carlos, fluid, temperature and available flow, pressure or head data. For replacement, add the equipment model, identification and drawing. Also state the destination and purchase documentation requirements. The team confirms any additional data needed and the technical and commercial proposal scope.

Yes. Projects in Antônio Carlos are handled by the factory team in Cabreúva, Brazil. Send your industrial requirement and the data already available. Configuration, availability, transport and any on-site service are confirmed according to the requested scope.

It depends on the series. Installation and operation instructions are in FBEI manual MAN001-10 and in FBME service manual MSERV-08/01, which also covers maintenance and recommends FB-authorized supervision during installation. The FBE (MTEC-01/01), FBCN (MTEC-03/00) and FBOT (MTEC-16/00) technical manuals provide technical data, sectional drawings, parts lists and dimensions; for installing and maintaining these series, the published services include on-site start-up and commissioning and maintenance contracts. The manuals are on the website’s technical manuals page (PDFs in Portuguese), and MSERV-08/01 is on the FBME series page. For the operation in Antônio Carlos, identify the series and model from the pump’s nameplate.

It depends on the series, as set out in each manual: 10 kgf/cm² for the FBE (MTEC-01/01, Table 5), 1.5 times the operating pressure for the FBOT (MTEC-16/00), 1.5 times the working pressure for the FBME (MTEC-08/01) and per ANSI B73.1 for the FBCN (MTEC-03/00). The test is performed on the factory bench in Cabreúva, Brazil; certificates, additional tests and customer witnessing are defined in the proposal for supply to Antônio Carlos.

FB Bombas reports a registration in the Petrobras supplier registry (CRC, formerly CRCC). It is a supplier registration, not a product certification; validity and supply families appear on the current certificate, provided on request. Technical standards depend on the series: mechanical construction per ASME B73.1 for the FBCN, NFPA 20 or ABNT NBR 16704 for FBFS fire pump sets when the project requires it, and API 610 for engineered-to-order projects. These bodies publish standards; they do not certify the company. Tests and certificates for each supply are defined in the proposal.

It can, especially with viscous fluids. On the FBE, speed and transmission are set by fluid viscosity (Table 2 of manual MTEC-01/01), and the heating chamber is available only on sizes from 1.1/2" to 6". The FBEI manual requires the fluid to be at the proper temperature and viscosity before start-up and the heating jacket to be supplied gradually, with steam up to 185 °C or thermal fluid up to 232 °C, both up to 10 bar. State the minimum site temperatures and the fluid viscosity at start-up and in operation in Antônio Carlos.

Yes, when they are included in the purchase scope. The published services include bench performance testing with a scope defined for the project, and on-site start-up and commissioning based on the manual and site conditions. Procedure, test points, acceptance criteria, customer witnessing and reports are defined in the proposal before the supply for Antônio Carlos is contracted.