FBE Gear Pumps in Santo Antônio do Tauá

Yes. With a factory in Cabreúva/SP and a technical team dedicated to projects in Santo Antônio do Tauá, FB Bombas has manufactured industrial pumps in Brazil since 1944. Applications currently running on imported equipment are covered by the FBCN (centrifugal), FBE/FBEI (gear) and FBOT (thermal oil) series — adding advantages in lead time (no import), factory-direct technical support, spare parts for FB pumps and application engineering that works in Portuguese. In a normalized-line retrofit, the interchangeability set out in ASME B73.1 holds between units of the same standard dimension designation, whatever the original supplier.

Yes. On pumps installed in Santo Antônio do Tauá, FB Bombas application engineering applies ISO 10816 (velocity RMS in mm/s) to diagnose misalignment, imbalance, bearing defects and cavitation. The scope covers baseline captured at startup, spectral comparison throughout PM campaigns and recommendation of interventions — re-balancing, bearing replacement, laser alignment — before the machine reaches the standard's zone D.

Yes. The design of the FBE and FBCN lines favors direct access to wear-prone components — disassembly and inspection are done with conventional tools. The routine gets even simpler with detailed technical manuals and replacement parts supplied straight from the factory.

For critical parts (mechanical seal, impeller, shaft, wear ring, bearings) during a plant shutdown in Santo Antônio do Tauá, FB Bombas runs an emergency flow: pre-invoicing, priority dispatch and alternative modal (express road or air transport depending on distance and criticality). Typical lead time varies by region, with a window negotiable case by case. For customers with an installed base and scheduled PM, part of the stock can be kept on consignment at the plant.

Yes, provided the dimension designation coincides. By following ASME B73.1 — the North American dimensional standard for end-suction process pumps — the FBCN occupies the standardised installation envelope defined by the norm, which does not depend on who built the pump running in Santo Antônio do Tauá plants. What is supplied is the complete pump: baseplate, suction/discharge piping and foundations usually remain. FB application engineering runs the dimensional gap analysis before supply, covering flow, head and required NPSH as well.

Yes. FB Bombas manufactures pumps for stationary fire protection systems in compliance with NFPA (National Fire Protection Association) and ABNT NBR 16704 standards, serving building and industrial projects that require these certifications.

Yes. The FBCN series complies with ASME B73.1 (North American standard for horizontal end-suction process centrifugal pumps) — which enables retrofit on existing baseplates in Santo Antônio do Tauá plants, whoever manufactured the installed unit, provided the dimension designation matches. Shaft dimensions, suction/discharge flanges, casing feet and impeller centerline follow the standard: the complete FBCN pump goes in and piping and baseplate stay put.

FB Bombas manufactures four major lines: FBE (external gear) for viscous fluids, FBEI (internal gear) for lubricating fluids, FBCN (normalized centrifugal) for water and low-viscosity fluids, and FBOT (specific centrifugal) for thermal oil circuits. We also serve fire protection systems in compliance with NFPA and NBR 16704.

Maximum temperature depends on the series: FBE and FBEI operate up to 350°C with heating jacket and special sealing; FBOT operates up to 350°C in thermal oil circuits; FBCN operates up to 260°C with proper materials and sealing. Correct sizing of sealing and materials is essential for safe operation.

Send the application data through the website form, WhatsApp +55 11 97287-4837 or email comercial@fbbombas.com.br: fluid (name and viscosity at operating temperature), target flow in m³/h, discharge head in m, available NPSH, operating temperature and regime — continuous or intermittent. After reviewing the briefing, application engineering returns a preliminary technical proposal, characteristic curve, suggested materials and delivery lead time for your project in Santo Antônio do Tauá.